Block 1, Practice Appraisals (Combined)

2B. Establishment of a low-impedance path between two metal surfaces describes what?

2C. Which of the following is NOT a category of failure caused by ESD damage?

2D. Your main role in facility security requirements is knowing the requirements for your unit of assignment and _______

11A. Wiremaps and Delay skew are two of the possible advanced features you could find on a Connectivity Test Set

11A. When a technician needs to locate a single cable in a large bundle of cables, what would be the appropriate tool?

9C. This type of access point does not make forwarding decisions, but passes data to the Wireless LAN Controller (WLC)

2D. Physical security requirements for a particular facility are primarily dependent on several things, including

11A. If a technician needed to secure or resecure cable ends on a copper cable what should they use?

4A. Web browsers such as Chrome, Firefox, and Edge are found at which layer of the OSI Model?

6C. User Datagram Protocol is found at the transport layer of the OSI model.

5A. When you have multiple subnet masks on one network, it is said to be a

5A. Which of the following is a Class B IPv4 address?

2C. Which of the following is NOT a proper handling precaution for Electrostatic Discharge Sensitive items (PICK ONE)

2C. One general precaution is to avoid testing ESDS devices with a multimeter.

12C. ________ are easier to jam than spread spectrum signals and transmit on one set frequency

6B. Which of the following are features of Transmission Control Protocol

5A. Which of the following is a valid Internet Protocol version 6 address?

5A. Convert 1110₍₂₎ to its decimal equivalent

2A. Earth electrode, equipment fault protective, and signal reference are all subsystems to what?

2A. What type of hardware is NOT part of the earth electrode subsystem?

11A. What does a Light meter check for?

5A. Internet Protocol version 4 (IPv4) subnets are created by borrowing bits from the host portion of the IP address.

7A. The sole purpose of the Core layer of Cisco’s hierarchical internetworking model is:

7C. _________ of Cisco’s hierarchical internetworking model deals with users directly connecting to the network

7B. _________ is the communication point between Access Layer & Core Layer in Cisco’s hierarchical internetworking model

4A. On the network layer of the OSI Model utilizing ARP, IP addresses are translated into ________ addresses.

5A. Which of the following represents a Class A network?

9C. Which type of access point is installed without authorization on a secure company network?

8A. Which of the following is NOT one of the basic functions of Network Monitoring Systems?

4A. Operating systems such as Microsoft Windows and Linux would lie at Layer 6 Presentation layer of the OSI model.

12B. Which of these is NOT an attribute of fiber-optic cables?

6C. _________ is used when speed is of primary importance.

12C. _________ are more difficult to jam than fixed frequency signals and transmit across a broad frequency bandwidth

2A. Which of the following are methods of electrical noise reduction?

2A. Shutting down the affected circuit whan a dangerous electrical current is detected is performed by what equipment?

6D. Registered virtual ports are in a range of 1024 to 49151 and are assigned by Internet Assigned Numbers Authority.

11A. If a technician wanted to check for a break in a fiber line, what would they use?

8A. What NMS function provides real-time and historical network status reporting?

2A. Total opposition to current flow within an electrical circuit is called _____________.

2A. In multipoint signal reference subsystems, equipment cabinets are commonly bonded to a common interior sheet or grid

10A. In which step of troubleshooting methodology do you record problem findings and solutions for future use?

5A. Which of the following is a valid Internet Protocol version 4 (IPv4) address?

12A. What is NOT one of the configurations found in the T-568A/B pin out standard?

5A. Convert CF1₍₁₆₎ to its binary equivalent

8A. Simple Network Management Protocol (SNMP) is critical for the functionality of Network Monitoring.

6B. Guaranteed delivery of information would best describe what type of protocol?

9A. What does a Wireless Local Area Network (WLAN) utilize to join two or more devices onto a network?

9A. Which of the following statements regarding wireless networks is False?

2A. What is a conductive path for reducing the possibility of shock/static buildup between the earth and ground?

5A. Dotted decimal notation is the format for this type of address ________.

4A. Electrical impulses, light and radio signals are used to convey data on the _________ layer

5A. Written as a subscript, the ____________ identifies the number system and identifies the quantity of Arabic numerals

5A. Convert 71₍₁₆₎ to its binary equivalent

8A. The Alert Network Monitoring System function

2A. The ____________ refers to a conductive sheet or grids that places all points on the network at the same potential.

9B. The most common example of a PAN, ________ is a global 2.4 Ghz for short range wireless communication

2C. Affected equipment will sometimes work correctly and sometimes not describes what type of ESD damage?

12A. How many insulated wires are found in Unshielded and Shielded twisted pair cable?

2B. Which type of bond which is generally welded or brazed and is expected to remain intact for the life of the system?

6C. Data that is sent with no guarantees that the data will reach the recipient describes what type of communication?

12C. By superimposing information onto an RF Carrier, ___________increases power and range of the signal.

7. There are___ layers in Cisco’s hierarchical internetworking model

9A. IAW IEEE 802.11 wireless network standard, ______is a collection of wireless networking devices with same parameters

9A. Also known as a name, what IEEE 802.11 wireless network standard tells you what network to join?

12A. Which is NOT a benefit of using Shielded Twisted Pair (STP) cable

9C. Autonomous access points have all software required to manage WLANs with no need for controllers or switches.

2D. Which of the following is an example that would be require a No-Lone Zone?

5A. Convert 11001110₍₂₎ to its hexadecimal equivalent

9A. This piece of equipment connects to a wired router or switch and is critical to a wireless network

6D. Which organization maintains and assigns port numbers for specific usage?

11A. __________is a software troubleshooting tool that will display and allow editing of the local system routing table

6D. Well-Known ports, also known as system ports, range from

11A. If a technician wanted to observe the frames on the network, what should they use?

5A. Which of the following is a correct representation of 255.255.255.192 in Classless Internet Domain Routing notation?

2A. The primary functions of Grounding are: equipment protection, personnel safety, and electrical noise reduction.

4A. The application layer (OSI Layer 7) is farthest away from the end user. (True or False)

5A. A number that is written in "base 16" has been written in what numbering system?

8A. The Monitor NMS function provides administrators with Ping availability, latency, CPU, and memory status

5A. A subnet is a logical division of a network of connected devices based on _____________.

9A. Some devices on a Wireless network may also be connected using Ethernet cables? (True or False)

4A. Home of the operating system, this layer translates data from application to network format and vice-versa.

2B. Bonds between unlike metals are highly susceptible to _______.

2C. Immediate total failure of the affected equipment describes what type of ESD damage?

4A. Which layer of the OSI Model sets up, coordinates, and terminates connections between the applications on each host

10A. What is based on idea that effective management should solve the underlying problem instead of treating symptoms

10A. The first thing you should be aware of when troubleshooting a problem is that the symptoms are not the problem.

2C. What is the sudden electric flow between two electrically charged surfaces?

8A. The _____ function in a Network Monitoring System is used to visualize the network?

4A. The router, which is known as a "layer 3 device", resides on which layer of the OSI model?

8A. ________ looks for signatures of known attacks or deviations from normal activity

2B. Bonding straps must be mechanically strong and

12C. Which of the following is FALSE regarding wireless transmissions?

4A. What are the Seven Layers of the OSI model?

2D. A special access badge and a purpose to be in an area describes what type of area?

2B. With the exception of high-vibration environments, which of the following is preferred for indirect bonds?

11A. If a technician wanted to test a Wi-Fi’s signal strength on a job site what would they use?

7. Cisco's internetworking model consists of which layers?

10A. Being the first step in troubleshooting methodology, this where you find what is causing the symptoms to manifest

5A. Which of the following numbers are written in hexadecimal format?

5A. Convert 471₍₁₀₎ to its hexadecimal equivalent