State Test #1 W2

Chain clamps are used to align and hold pipe for _____.

In which of these processes is acetylene used?

Compared to a single V-groove weld, a double V-groove weld _____.

In plasma arc cutting, plasma is created by _____.

heavy-duty pac systems require a gas cylinder (cutting gas) and another containing _____.

Most work site fires related to welding operations are caused by _____.

Grounding of a welding machine usually involves _____.

When applying a fillet weld to an outside corner joint, ASME approves of the _____.

Gouging root welds and seams is best done by _____.

Which of these metals has been linked to Parkinson's Disease?

Internal misalignment between 2 sec of pipe to be welded end to end is checked using a _____.

Surfacing welds can be used to _____.

The most common welding accident is _____.

How close should a high vacuum/low volume exhaust inlet be located to the welding fumes?

Common grade stainless steels are classified by their _____.

Cutting a 2" (5 cm) aluminum plate requires a(n) _____.

Cutting metal with oxyfuel, plasma arc, or air-carbon arc processes is referred to as _____.

The degree of distortion that happens during welding is directly related to the _____.

Which of the following is a correct statement regarding personal protective equipment?

Which of these welding methods uses a flux-coated consumable welding rod?

The tool that uses a bubble in a glass vial to check level and plumb is a _____.

What concentration of oxygen, in percent by volume, is considered normal and safe to work in?

Which of the following safety statements related to plasma arc cutting is true?

Welded pipe fittings _____.

The proper selection of a respirator is based on the _____.

All of the following fabrics may be worn around sources of sparks or high heat except _____.

When 2 pieces of metal are welded end-to-end and forces are applied inwardly from each end its

The most common weld defect caused by surface contamination is _____.

Excessive face reinforcement _____

Nibblers prepare the edge of base metals using a _____.

When aligning a joint fit-up, an open-root joint should have a root opening from _____.

Common-grade stainless steels normally contain at least _____.

In the oxyfuel cutting process, which of the following is used as a fuel gas?

The term standoff distance refers to the _______.

When using a chain fall secure the chain fall to overhead structural member with approved ____.

In most cases, plasma arc cutting is _____.

When gas cylinders are disconnected from a pac unit before it is stored, be sure to _____

An air-purifying respirator should be changed _____.

Foot and vehicle traffic in the workplace is _____.

Largest of the three common stainless steel is the _____.

The simplest plasma arc cutting units use filtered _____.

As the carbon content of carbon steel rises, the steel becomes _____.

Which of the following PPE is considered optional for plasma arc cutting?

Compared to a full leather welding jacket, a welding cape is _____.

Industrial plasma cutting units can cut carbon steel up to _____.

Which of these is the correct statement regarding SDSs/MSDSs?

The risk of flash burn can be reduced by _____.

Procedure in which 2 people perform welding sequences on opposite sides of a joint at same time

Letter A in front of year on the cover of the ASME code indicates that the code contains ____.

Some light-duty PAC equipment has a built-in _____.

Sputtering or hissing of the torch is often caused by _____.

One of the joints used with a plug and slot weld is a _____.

To pierce very thin metal using plasma arc cutting, hold the torch at a _____.

Welding sequence with short welds ____ joint is recommended to reduce the effects of shrinkage.

Always try to position the weldment so that welding is performed in the _____.

The gap plate of a plate alignment tool can be changed to match the specified _____.

The most common plasma arc cutting torch uses _____.

Considering the two joint preparation methodsmechanical and thermalthe mechanical method

The typical plasma arc cutting torch contains a _____.

The recognized national standard in the United States for safety in welding is _____.

Which statement is correct regarding the cleaning of base metals before welding?

A doc that allows a welder to perform operations where there is a potential risk of fire is a _.

Apprenticeship programs in the United States must be registered with _____.

For tasks in which 100 % weld and grind is required before the clamp is released. Use a

The groove angle for welding open-root welds on plate is typically _____.

A detailed listing of the rules and principles that apply to specific welded products is a ____

The centering head attachment of a combination square is used to measure _____.

In addition to protecting other workers from exposure to electric arcs, welding screens _____.

The requirement for the use of a WPS is often on the _____ or in the tail of the welding symbol

The results of testing the WPS for a job are recorded on a(n) _____ and kept on file.