NCCER MODULE 00101-09 Basic Safety TRADE TERMS

Question 1

When climbing a ladder or scaffold, use one to pull up your tools.

Accepted Answer

hand line

Question 2

A narrow excavation made below the surface that is generally deeper than it is wide

Accepted Answer

trench

Question 3

The conducting connection between electrical equipment or an electrical circuit and the earth

Accepted Answer

ground

Question 4

Nonadjustable and consists of two rails, rungs between the rails, and safety feet

Accepted Answer

straight ladder

Question 5

Refer to this to learn about how to handle hazardous substances

Accepted Answer

material safety data sheet

Question 6

Tells you which way the wind is blowing

Accepted Answer

wind sock

Question 7

Liquids that should be stored in safety cans to avoid the risk of fire.

Accepted Answer

flammable

Question 8

A chip or fragment of rock or soil that has been broken off from the main mass

Accepted Answer

spall

Question 9

An assembly of machines used to do a particular job

Accepted Answer

apparatus

Question 10

Exceeding this on a ladder, can cause ladder failure

Accepted Answer

maximum intended load

Question 11

An OSHA rule requiring all contractors to educate their employees about hazardous chemicals

Accepted Answer

Hazard Communication Standard (HazCom)

Question 12

Exposure to the ultraviolet light from arc welding can cause a(n)

Accepted Answer

flashburn

Question 13

The temperature at which a fuel gives off enough gases to burn

Accepted Answer

flash burn, flash point

Question 14

It is placed halfway between the toeboard and the top rail

Accepted Answer

mid-rail

Question 15

A type of scrap material that catches fire and burns easily

Accepted Answer

combustible

Question 16

Piece of wood or metal placed diagonally from the bottom of one rail to the top of another rail

Accepted Answer

cross-bracing

Question 17

Use only approved ones for plugs

Accepted Answer

concealed receptacles

Question 18

Sudden, bright light that occurs when you start up a welding operation

Accepted Answer

flash

Question 19

Manufactured and rolling are the two basic types of

Accepted Answer

scaffold

Question 20

A protective screen used when you are welding and other workers are near by

Accepted Answer

welding shield

Question 21

To prevent a cave-in, follow OSHA regulations for

Accepted Answer

shoring

Question 22

A vertical barrier used at floor level on scaffolds to prevent materials from falling

Accepted Answer

toeboard

Question 23

Publishes rule, and regulations that employees and employers must follow

Accepted Answer

Occupational Safety and Health Administration

Question 24

If fuel is improperly mixed, it can cause a(n)

Accepted Answer

flashback

Question 25

When doing this, you must be careful not to come into contact with the nearby hazard

Accepted Answer

proximity work

Question 26

Helps prevent or correct conditions that can cause accidents

Accepted Answer

management system

Question 27

A horizontal board used at top-level on all open sides of scaffolding and platforms

Accepted Answer

top rail

Question 28

Houses the circuits that distribute electricity throughout a structure

Accepted Answer

electrical distribution panel

Question 29

The cutting process results in oxides that mix with molten iron and produce

Accepted Answer

dross

Question 30

A general construction rule that states that fall protection is required when working 6 feet up

Accepted Answer

six-foot

Question 31

A device that interupts and de-energizes an electrical circuit to protect a person

Accepted Answer

ground fault interrupt circuit

Question 32

Large enough to work in but has limited means of entry or exit; sometimes a permit is required

Accepted Answer

confined space

Question 33

A unit of measure of the intensity of light falling on a surface

Accepted Answer

foot-candle

Question 34

Never look at this caused by welding without proper eye protection

Accepted Answer

arc

Question 35

Includes a face shield, ear plugs, and gloves

Accepted Answer

personal protective equipment

Question 36

Provides clean air for breathing

Accepted Answer

respirator

Question 37

Someone who directs someone operating a vehicle on a job site

Accepted Answer

signaler

Question 38

Houses electrical switches used to regulate and distribute electricity in a building

Accepted Answer

switch enclosure

Question 39

A self-supporting ladder made of two sections hinged at the top

Accepted Answer

stepladder

Question 40

Pieces of material at least 2 inches thick and 6 inches wide used as flooring, or decking

Accepted Answer

planked

Question 41

The waste material from welding operations

Accepted Answer

slag

Question 42

Identifies unsanitary, hazardous, or dangerous working conditions

Accepted Answer

competent person

Question 43

The process of joining metal parts by fusion

Accepted Answer

arc welding

Question 44

A formal procedure for taking equipment out of service.

Accepted Answer

lockout/tagout

Question 45

Has proven his or her extensive knowledge, training, and experience

Accepted Answer

qualified person

Question 46

Any man-made cut, cavity, trench, or depression in an earth surface, formed by removing earth

Accepted Answer

excavation

Question 47

An opening in a wall or floor must be either covered or

Accepted Answer

guarded

Question 48

Before working here, you must be trained, obtain written authorization, and take precautions

Accepted Answer

Permit-Required Confined Space

Question 49

When doing work more than 6 feet above the ground, you must wear a safety harness with a

Accepted Answer

lanyard

Question 50

Two straight ladders that are connected so the length of the ladder can be changed

Accepted Answer

extension ladder

NCCER MODULE 00101-09 Basic Safety TRADE TERMS

Questions 50

NCCER MODULE 00101-09 Basic Safety TRADE TERMS

Questions 50