Year 1 exam 1 part 2

Three things that would make a sledge unusable are a ____head, a loose head, or a damaged handle.

After completing a full report, the OSHA compliance officer is responsible for determining the amount of fines.

Employers are not required to provide their employees the necessary training required by OSHA standards.

All tools shall be kept in good working condition, properly stored, and must be _____

When should a plane test be performed?

The person responsible for sharpening & properly shaping the climbing gaff's is the manufacturer.

Guy wires cannot become energized because they are tied to rods in the earth.

It is the purpose&policy of the ___to:assure as far as possible every man in the nation safe and healthful work conditon

The OSHA industry standard that would cover the construction of a new overhead transmission line is 29 CFR _____

A pole that is over ___ old should be supported with a line truck boom or other device in case in its unstable.

The proper placing of small tools in body belt is not an issue because they cannot make contact with energized parts.

There are 2 types of variances that can be issued by OSHA to an employer, these are temporary and ____

According to OSHA, the employer is NOT responsible for _____

Objects that are (insulated) from ground are ______

The _____ electricity must be a main point of emphasis for any company or safety program.

A piece of ____ can be placed between the load and the head of a jack to prevent a load from slipping off the jack.

The neutral conductors are normally connected to the _____

If employee is exercising their OSHA rights, the employer is not permitted to __ against that worker in any way.

The one with responsibility for inspecting, maintaining, & rejecting climbing equipment is the ____

Safety is a thought process and should never be allowed to become a(n) _______

Tools not in use shall be returned to their designated storage space.

A handtool such as a chisel is unsuitable for use if it had a ____

Most electrical conductors are made of copper, aluminum, or ____ in older systems.

An electrical workers side cutting pliers should never be used as ______

The OSHA poster #3165 “its the law” is required to be posted in a prominent location for access by all of the workers.

The use of a ____ tape measure is prohibited on or near energized equipment or lines.

Accidents associated with hand tools account for _____ of cases per 10,000 workers in the workplace compensable injuries

A qualified electrical worker must be _______

A capacitor stores electrical energy.

The ability to work with other people in harmony is known as _____

The normal operating voltage of electrical equipment must be determined by workers _______

Upon arrival to perform a worksite inspection, an OSHA inspectors first step is to ______

Unless fully protected, edged or pointed tools shall not be carried in ______

Climbers should be inspected for_____

The climber straps and pads should be inspected for ____

Wrenches shall never be used _____

When using a sledge hammer, always be certain that others are out of reach of the back swing.

If a wrench handle is too short, a piece of pipe may be used to lengthen it in order to gain added leverage.

The tip of the gaff should have a spike point.

The term nominal voltage means the _____

Ordinary plastic dipped handles on wrenches are designed to provide electrical insulation.

Ways to determine the actual operating voltage of a power line include asking authorized represent, name plate info & __

During a pole cut out test, the proper procedure is to _____

One good climbing practice that will help avoid accidents is practice taking extra large steps when ascending,climbing..

The safest way to cut with a knife and keep control of it is to cut towards the body.

Prior to the formation of OSHA, job related accidents accounted for nearly ____ worker deaths per year.

The _____ of impact tools is to be avoided, and such impact tools are to be kept dressed down.

Hazards from tools can be placed in 2 broad categories; 1 is danger from the tools action, & danger from ______.

The OSHA act was signed into law in _____.

An improperly sharpened gaff is safer than a gaff that has not been sharpened at all.

An employee representative is permitted to participate during an on site OSHA inspection.

When climbing a pole,carrying the handline on a breakaway hook will help eliminate the hazard of being pulled off pole

The US congress passed the OSHA act in 1970 because of the horrific statistics on workplace deaths and injuries.

If accidents are to be reduced on the job, the climber must develop a safety conscious attitude.

When storing sharp tools, sharp edges and points shall be covered with ______ guards.

The device used to automatically raise or lower the primary voltage of a line to ensure it's optimal voltage range is___

A qualified individual understands that all conductors must be _____

Tools shall not be left atop poles or any part of a structure, _____, or scaffold.

OSHA has the legal authority to, without delay, and at reasonable times _____

OSHA has divided the US into ____ regions.

Each OSHA region is divided into local area offices; the title of the person in charge of these offices is _____.

Under OSHA regulations, a violation that has a substantial probability to cause death is called a ____ violation.

A body belt with a pole strap is an example of a fall ____ system.

Under OSHA regulations, the employee is not responsible for _____

OSHA regulated electric power generation, transmission, and distribution through the regulations at 29 CFR ____.

OSHA has ____ in which to complete an investigation.

The operating voltage of an insulator can be determined by the _____, it's length, or it's height.

The greatest hazards posed by hand tools are ____.

When using electric power tools, one should always use a 3-wire cord with ground.

The electrical factor distance and human factor distance are also called the ____

The ultimate goal of OSHA is to reduce injuries, illnesses, and death of workers to ______

If worker thinks they are being punished for exercising their OSHA rights they have to contact OSHA in ____.

To help prevent climber cutouts, gaff's must be sharp, properly sized, and properly shaped.

Cable cutters should be adjusted and lubricated _____ when in use.

When an employer fails to correct previously cited OSHA violation beyond a prescribed date, it is called a failure to __

The gaff is properly shaped and sharpened when it begins holding a distance of ____

Climber shank and sleeves should be inspected for _____

The approach distance to a 12,000volt line phase to phase is _____

When performing the cut out test, at what distance should the gaff be pushed into the pole?

The parts of an electrical system used to isolate conductive (energized) material from other parts are called _____

The purpose of the OSHA act is to provide every working man in the nation with a guaranteed safe and healthful workplace

Electrical circuits may be in an ____ configuration.

Files may be struck with a hammer when additional pressure on the file is needed.

Conductors are the part of an electrical system that carries electrical current.

Insulator installed in guy wires are intended to protect _____

By law, every employer covered by the OSHA act must comply with any standards, rules, regulations issued by OSHA

The piece of equipment used to step the voltage up or down in an electrical system is called a ____

The connection point between an underground cable and an overhead conductor is normally made through a _____

Knots and knotholes are not hazards that contribute to cutout accidents because the gaff's are shaped to deal with them

Any on the job accident that results in the death of___ employees must be reported to the nearest OSHA office w/in 8 hrs

The OSHA act covers workers employed in ______

The point of the gaff should cut the pole surface at a maximum of two inches.

A qualified worker must be trained and have the ability to recognize _____

According to the “code of federal regulations” a ____is to be worn when working from an aerial lift.

Everyone, except qualified employees, must stay at least _____ from apparatus energized up to 50,000 volts.

A screwdriver shall not be used as a punch or a _____

When a voltage condition occurs that is higher than the designed voltage for the system, a ___becomes a path to ground.

NFPA 70: national electrical code is 1 of 2 consensus standards that provide requirements for electrical safety

If the gaff slides along the wood without digging, then the gaff is either improperly sharpened or gaff angle 2 small

When using a socket set, it is best to use one size handle, and adaptors on different size drive sockets.