An important topic to include in safety orientation is the

process used to communicate safety concerns

Ergonomics can best be described as

Adapting the work area to fit the person to reduce stress

When observing a worker performing a lockout/tagout, what observations listed below would cause you to stop the worker?

The worker does not test all energy source after locking out of equipment.

Safety Data Sheets (SDS) are required by OSHA to be

Readily available to employees in their work area

A(n) __________ is a labeling system designed to quickly and accurately identify hazardous materials.

Hazardous Material Identification System

Documentation of inspections for emissions released into the atmosphere is regulated by the

Environmental Protection Agency

An evacuation alarm just went off, what should you do?

Initiate emergency shut down procedures and evacuate

A worker should not unload a truck if____________.

they do not understand a placard on the truck

A pedestrian who is working in areas where forklifts are operated should __________________.

Use the marked aisles and designated doors for pedestrians

Suggestion for changing or improving safety training materials or content should be

Given to safety representatives or trainers for their evaluation

When performing a monthly inspection of the fire system, an inspector should _______________________.

Check the dates on the fire extinguishers

The Department of Transportation (DOT) oversees the ___________.

transportation of hazardous materials

All OSHA required training includes making which of the following available to workers who are being trained?

the facility’s emergency plan

One benefit of having employees who are cross-trained is

Flexibility in assigning working to specific jobs

All Industrial Injuries must be reported to

The team leader or supervisor immediately

Waste materials such as scrap metal in an open yard are a possible________.

Storm water contamination source

An effective way to kill any potential blood borne pathogens is to _________.

clean the blood spill with a 10% solution of bleach and water

Suggestion gathered in a Safety Suggestion Box

Should be systematically documented and followed up when appropriate

Conducting a Job Safety Analysis is warranted when ____________________.

A new piece of equipment is installed

NFPA uses which of the following color codes?

Blue = Health, Yellow = Reactivity, Red= Fire and White = Information

Company’s should track on going safety concerns at their facility

Until corrective action is taken to address the problem

The team leader of High Performance Team

Has the authority to make the decision if the team is deadlocked

Which of the following should be checked when inspecting eye and face protection?

Damage, appropriate rating and proper fit

After a new production employee has been through the safety orientation

their participation is documented according to company policy

First aid training enables a person to provide ______________.

first aid until professional medical assistance arrives

As a safety precaution at a workstation, a compressed gas cylinder should be

Chained to a rigid item next to the workstation

studbud

MSSC Safety

90 termsStudBud Administration259 plays

Imported from external platform

Flashcards90 cardsFPractice quizPHost liveL

Questions 90

Answers

1
An important topic to include in safety orientation is the
process used to communicate safety concerns
process used to change equipment operation procedures
name of the person who does safety inspection
method used for scheduling refresher training
2
Ergonomics can best be described as
Adapting the person to fit the job to reduce stress
Providing adequate work space
Providing a new work facility
Adapting the work area to fit the person to reduce stress
3
Who ios on the $10 Bill
Jefferson
Hamilton
Franklin
Burr
4
A decision-making process where all team member accept the same decision is called
democratic
autocratic
consensus
unanimity
5
The _____________ is a guideline published by the American Conference of Governmental Industrial Hygienists
Threshold Limit Value (TLV)
Permissible Exposure Limit (PEL)
Poison Control Center Limit (PCCL)
Chemical Abstracts Service Registry Number (CAS NO.)
6
When observing a worker performing a lockout/tagout, what observations listed below would cause you to stop the worker?
The worker does not test all energy source after locking out of equipment.
The worker uses a Hasp or Lock Boxto allow lockout by more than one person.
The worker places an identification tag on the lock.
The worker places an identification tag on the lock.
7
When working with sharp or rough metals, a sheet metal worker should
Wear gloves and safety glasses
Use sandpaper to remove the rough edges
use cotton gloves
file the edges of the metal smooth
8
The emergency response team should be notified immediately if you observe a(n) ____________.
Hazardous material spill
Machine guard that needs repair
Inefficient work process
Employee showing up late
9
Which industry sector uses IIoT to remotely control energy-consuming devices?
Aerospace
Manufacturing
Transportation
Energy and power
10
Safety Data Sheets (SDS) are required by OSHA to be
On display in the plant medical area
Stored in the plant manager’s office
Stored in the Safety Committee Office
Readily available to employees in their work area
11
A(n) __________ is a labeling system designed to quickly and accurately identify hazardous materials.
Hazardous Material Identification System
DOT
SDS
Hazardous Communication Standard
12
Documentation of inspections for emissions released into the atmosphere is regulated by the
American Society of Testing Materials
Department of Energy
Environmental Protection Agency
Nuclear Regulatory Commission
13
An evacuation alarm just went off, what should you do?
Leave your work area and go to the exit door
Initiate emergency shut down procedures and evacuate
Go see what everyone else is doing.
Continue working until supervisor says to evacuate
14
A worker should not unload a truck if____________.
it is facing down hill
they do not understand a placard on the truck
they do not know the driver
it has been sitting more than six hours
15
A pedestrian who is working in areas where forklifts are operated should __________________.
Realize drivers are responsible for safe forklift operation at all times
Accept a ride from the driver on the forklift
Use overhead door way to go out side
Use the marked aisles and designated doors for pedestrians
16
A Class A Fire Extinguisher is used for burning _________________.
Paper
Liquid
Oil
Magnesium
17
Ear plugs should be replaces when they are no longer___________.
rigid
inflexible
pliable
Covered by the warranty
18
The bottom of a _________ respirator presses against the skin between the mouth and chin.
Quarter-mask
Half-mask
Full-mask
Hood
19
Suggestion for changing or improving safety training materials or content should be
Sent suggestion to corporate office for evaluation
Given to the plant manager
Given to safety representatives or trainers for their evaluation
Disregarded because the standards are set be OSHA
20
Recognizing and reporting improperly guarded equipment is the responsibility of
The safety department
The supervisor
The team leader
everyone
21
The primary reason for training needs in today’s manufacturing
To receive grant money
To involve employees
Change in people/Processes
Job justification
22
An___________ interlock physically prevents a machine’s from operating when the guard is out of place.
electrical
mechanical
pneumatic
hydraulic
23
When performing a monthly inspection of the fire system, an inspector should _______________________.
Reset the Fire Alarm Control Panel (FACP)
Test the operation of the sprinklers
Not disturb the fire house pump
Check the dates on the fire extinguishers
24
The Department of Transportation (DOT) oversees the ___________.
transportation of hazardous materials
adherence to proper sound levels
licensing of fork lift drivers
All of the Above
25
All OSHA required training includes making which of the following available to workers who are being trained?
a copy of all records and notes from safety committee meetings
the facility’s emergency plan
a copy of the OSHA standards referred to in the training
a copy of 29 CFR 1910
26
To protect your hands, you should only wear gloves approved by __________.
OSHA
NCAA
ASTM
STMA
27
Which of the following items marked the advent of the third industrial revolution?
Computers
Mass Production
Printing Press
Networking
28
The person who performs the next step in a production process is an ______to the person preforming the previous step.
internal customer
Assistant
supervisor
Supplier
29
All approved safety glasses must have_______ stamped on the frame.
BR529
B-29
A company name
Z-87
30
One benefit of having employees who are cross-trained is
Large workforces for all shifts
Employee turnover is higher
Flexibility in assigning working to specific jobs
Cheaper material cost for all products
31
The most common way for a chemical to enter the body is _____________________.
cleaning
ingestion
inhalation
clothing
32
All Industrial Injuries must be reported to
Corporate Safety and Environmental Management with in one hour
The team leader or supervisor immediately
The plant safety coordinator only if there 911 is called
OSHA within 8 hours
33
Waste materials such as scrap metal in an open yard are a possible________.
Raw parts source
Inventory problem
Storm water contamination source
Hazardous material problem
34
An effective way to kill any potential blood borne pathogens is to _________.
wear gloves while cleaning
clean the blood spill with a 10% solution of bleach and water
clean the blood spill with hot water and soap
clean the blood spill with dry ice
35
Standard introduced in the early 1980s established a method to physically connect machines from different manufacturers
Ethernet
WWW
OPC UA protocol
Cloud technology
36
Suggestion gathered in a Safety Suggestion Box
generally only useful in situations whenemployees fear reprisal management
Should be systematically documented and followed up when appropriate
Have been found to be a poor tool in the reduction of injury and illnesses
Are required to be addressed as part of the HAZCOM Standard
37
Conducting a Job Safety Analysis is warranted when ____________________.
There is an issue with an environmental permit
A new piece of equipment is installed
There is a need for improvement in productivity on a machine
A new employee is assigned to run a new machine
38
NFPA uses which of the following color codes?
White = Health, Red = Reactivity, Blue= Fire and Yellow = Information
Red = Health, Blue = Reactivity, Yellow = Fire and White = Information
Blue = Health, Yellow = Reactivity, Red= Fire and White = Information
Blue = Health, White = Reactivity, Red = Fire and Yellow = Information
39
Company’s should track on going safety concerns at their facility
So employees at fault can be disciplined
So that trainers know what safety concerns to warn new employees about
Until corrective action is taken to address the problem
Until management becomes aware of the problem
40
The team leader of High Performance Team
Influence the team toward management desire
Has the authority to make the decision if the team is deadlocked
Has no decision-making authority
Has equal decision-making authority with other team members
41
OSHA defines air as oxygen-deficient if it contains less than __________ percent oxygen.
16.5
21
23
19.5
42
Which of the following should be checked when inspecting eye and face protection?
Cost, manufacturing, and warranty
Damage, appropriate rating and proper fit
Heat distortion, lens color and manufacturer
Style, color and size
43
Company’s should provide refresher training on relevant emergency procedure and first aid to their employees every
bi-annualy
monthly
year
once per semester
44
The UN (United Nations) number for hazardous material is used for identifying
An international shipment
Which country the material should be shipped through
The Universal Notice of Intent to Destroy
The material being shipped
45
After a new production employee has been through the safety orientation
their refresher training should be scheduled immediately
their ready to work without additional training
Evidence of their participation is sent to OSHA
their participation is documented according to company policy
46
First aid training enables a person to provide ______________.
medical treatment to reduce a company’s health costs
the same level of care provided by a licensed nurse
first aid until professional medical assistance arrives
the same level of care provided by a licensed nurse
47
A floor distance of _______ should be free of combustible materials when welding and cutting.
25
10
20
35
48
How often is 8-hour HAZMAT refresher training required?
quarterly
semi annually
annually
monthly
49
As a safety precaution at a workstation, a compressed gas cylinder should be
Never be next to a workstation
In the corner of the workstation
Chained to a rigid item next to the workstation
Set at least 5 feet from the workstation
50
Which of the following is NOT an IIoT application?
Controlling your house thermostat with your phone
Viewing who is at your door from a remote location
Using your phone to see what is in your refrigerator
Monitoring in-plant processes
51
OSHA has set the permissible noise level at __________ decibels for an eight-hour period.
70
90
60
80
52
Company Fire Drills should include the date and time of the drill, the evacuation time and
the location of appropriate methods of egress
A description of any problems observed
The number of exits
The date of the next fire drill
53
Class G hard hats are _______ and provide some protection from contact with live electrical circuits.
designed for the electrical trades
conductive
called bump hats
non-conductive
54
Test results for employees who participate in environmental tests are required to be
Kelp locked in fire-proof cabinets
Displayed on the Company Safety Board with participant names
Shredded and disposed of in six months
Made available to test subjects
55
When walking in a warehouse facility, which of the following items is considered a housekeeping hazard?
A forklift parked with the forks in the down position
Oil or water spots on the floor
Materials stored on pallets
Chipped latex paint on the walls
56
A safe pedestrian walkway in a warehouse environment should include which of the following?
A pedestrian walkway door that is equipped with a peephole
One large door that is used by both pedestrians and fork trucks.
Mirrors to help control blind spots.
Be 2 ½ feet wide
57
If a worker sees a spill of a hazardous material, a worker should
Just ignore it
Notify the emergency response team
Grab a mop and get it cleaned up right away
Call the custodian
58
Name this President
Coolidge
Jackson
Clevland
Taft
59
Documentation of daily forklift safety inspection is required by the ______________________.
EPA
OSHA
DOT
NCAA
60
It is especially important that proper labeling be used with all ___________.
Conveyors
Hazardous Waste Containers
Shipping Pallets
Tool Boxes
61
Which of the following items can be disposed in a trash compactor in a landfill?
Paper Products
Full spray cans
Fluorescent light bulbs
Liquid dyes
62
Smart sensors connected to manufacturing networks creates what level of Industry?
Industry 2.0
Industry 3.0
Industry 4.0
ANSI Standard
63
To reduce unnecessary employee exposure to hazardous chemicals, employers can
Require employees to buy their own protective equipment
Provide EPA information to employees
Train employees how to use personal protective equipment
Eliminate use of all chemicals in the workplace
64
What items below is recommended for use on minor shin burns?
Blow on it
Cold Water
Hot Water
Dry Ice
65
Dr. Kings birth name is..........
Luke
LeMar
Michael
Martin
66
Which manufacturing logistics application includes the resources to move a product from the supplier to customer?
Logistics
Supply chain management
Customer support
Warehousing
67
Company employees should keep exit cleared and doors closed for fire prevention for what reason?
Fire Safety and Containment
Temperature control
Ventilation purposes
DOT requirements
68
In addition to a welding helmet, which of the following must also be worn for eye protection when welding?
Cutting goggles
Tinted lenses safety glasses
Safety glasses with side shields
Sunglasses
69
If a worker finds a safety guard by-passed on a machine, the worker should ______________________.
Immediately lock and tag out the equipment
Continue operation and fill out a suggestion
Complete a work order and then schedule for maintenance
Increase production to prepare for potential shut down
70
OSHA designate an oxygen-enriched level over __________ percent oxygen.
19.5
23
22
21
71
The ____________ labeling system was designed to help firefighters in the event of an emergency.
NFPA
UN
NCPA
DOT
72
Which IIoT application monitors equipment during normal operation to prevent failures to the equipment?
Logistics
Automation
Predictive maintenance
Customer support
73
To avoid potential fires, combustible materials must be kept a minimum of ____feet from any potential ignition sources.
25
35
10
75
74
One way to determine what safety improvements may be needed are to
Perform routine safety inspection
Complete production material usage reports
Conduct quality audits
Plan for regularly PM
75
What should you do if you are attending to someone who has swallowed a cleaning chemical?
Call 911 Immedieitlly
Force them to vomit
Give them antacid
Find the cleaning chemical and read the label
76
Which component of IIoT allows networked devices to exchange information?
Machine Learning
Machine-to-machine communication
Data Storage
77
Name This president
Jackson
Lincoln
Grant
Garfield
78
A Class D Fire is one that consists of burning______________.
Rubbish
Chemicals
Metals
Live Electrical Line or Equipment
79
To check for leaks on a half-mask respirator when inhaling, a worker should cover ______ with the palms of their hands.
Directional valve
Exhalations ports
cartridges
Sides of the mask
80
When preparing training materials, the presenter should
Communicate at a level appropriate to the audience
Prepare jokes from materials taught in the class
Use colored paper for handouts
Include multiple topics with many details
81
When providing effective training to new employees, the trainer should provide
An authoritarian environment
An authoritarian environment
Clear statements of expectation
A description of company training politics
82
A forklift operator should always drive the forklift in reverse when
The load is carried high
The load obscures the view forward
Driving up an incline
Navigating Sharp corners
83
Where caustics or acids are used, it is important that
All workers wear leather gloves
They are kept isolated in refrigerated containers
Only certified workers are employed in areas near caustic chemicals
Appropriate PPEs, emergency shower, and eyewashes are provide
84
Which of the following agencies require noise testing?
EPA
OSHA
NFTA
NCAA
85
A/an ___________analysis is a process of plaining the best method of integrating safety into the way a job is done.
Accident Report
Return on Investment (ROI)
Job Safety
Manpower
86
Tetanus is a possible result from ______________.
puncture wound from a nail
second hand smoke
broken bones
sprains
87
After providing training, what is the best way for a trainer to ensure employee can do the training objectives taught?
Pass the final written test for the class
Provide the employee with detailed procedures taught in the class
Observe the employee doing the training objectives taught in the class
Ask the worker if they fell they learned enough in the class
88
Job Safety Analyses (JSAs)
Should be reviewed on a regular basis
Should be included as part of the OSHA Injury and Illness Log
Are usually initiated after an accident
Are found in the manufacturer’s operation manual
89
When treating a puncture wound caused by a nail it is important to receive treatment for
Headaches
Tetanus
Swelling
Fever
90
The proper storage of inspection records is determined by
Federal Guidelines
State or local regulations
All of the above
Company Policy

MSSC Safety Flashcards | StudBud